grouselier7

Fiat 500 Replacement Key Fob It could be time to change the battery if the 500 remote key fob isn't working. If you replace the battery, but it doesn't work it could be the issue elsewhere. At United Locksmith, we specialize in making new keys for classic cars. We have the tools as well as the parts required for this type of service. Dead Coin Battery A dead battery is the most common cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob contains the battery of a coin-cell that can quickly deplete if it is not frequently used. If your remote has started to show signs of a loss of range, or has stopped working, then the battery may be dead. Metal clips keep the battery securely within the key fob. If the clips are loose, it can cause contact issues which will prevent the remote from receiving power. Using a small flathead screwdriver, pry the retaining clip to remove the battery and then insert a fresh one. Be sure to use an identical replacement battery type of voltage, size, and specification as the original battery. The key fob can also become corroded or damaged through exposure to water. Even a brief bath in soapy, warm water can damage the chip. Keep your key fob dry. Water Damage If your key fob isn't functioning properly, it may be due to water damage. The rubber seals on key fobs protect them from getting damaged by a slight drizzle or splash of water. However, it is crucial to keep your keys of your car away from the washing machine, ocean, and even the pool. fiat 500 key fob replacement comes with an electronic chip that sends a signal car's immobilizer system. The chip allows the 500 to be locked and started. If it gets wet, it will no longer work. If you're looking to determine whether your key fob functional it is possible to clean the internal electronics with isopropyl or an electronic cleaner. However, it's best to get a replacement from a dealer rather than trying to repair a key fob that is submerged in salt water. While a replacement fob might cost a bit of money, it's much less expensive than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also do it yourself with some simple steps. Be sure to have the correct type of battery before attempting to open your keyfob. You can find step-bystep instructions for any key fob in your car online. Faulty Chip The chip in the key fob communicates with your car's immobiliser unit to make sure your car is only able to start when the correct key is used. If the chip is damaged or damaged in any way the car won't start. A damaged chip could occur due to many reasons, but the most common cause is water damage or an unresponsive battery. It is best to hand over the repair to a professional locksmith who can replace the chip in a short time and at a a reasonable price. If your key fob does not function after exposure to water that is clean from the tap or rain take it off the battery. Wipe down the electronic component using paper towels. If the key fob will not work, there is the possibility that it has damaged components and requires to be replaced. Some people will turn to their dealer when in need of an entirely new Fiat key fob, however it can be a costly option. If you're seeking a cost-effective method to have your Fiat key fob fixed, look no further than United Locksmith. We have the tools and experience needed to repair your Fiat key fob in a quick and professional manner. Faulty Receiver Module Fiat key fobs transmit an electrical signal to the vehicle, which will unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. There are a variety of reasons why the fob may not function. This could be due to a dead battery, water damage, worn out buttons as well as a receiver issue. signal interference or malfunctioning chips. If the fob was placed in a pocket which has suffered extreme trauma (such as being dropped on the floor or washed in a washing machine) the fob might not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is a secure system that can only accept signals from a genuine original key and not accept any other. It is necessary to replace the fob if this occurs. A professional locksmith will handle the entire process of replacing your key including programming a new one for your 500. In fact, they can even provide you with a clone key that functions exactly like the original fob (and costs less than the cost).